 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| MAC15A6FP, MAC15A8FP, MAC15A10FP Preferred Device Triacs Silicon Bidirectional Thyristors Designed primarily for full-wave ac control applications, such as solid-state relays, motor controls, heating controls and power supplies; or wherever full-wave silicon gate controlled solid-state devices are needed. Triac type thyristors switch from a blocking to a conducting state for either polarity of applied main terminal voltage with positive or negative gate triggering. * Blocking Voltage to 800 Volts * All Diffused and Glass Passivated Junctions for Greater Parameter Uniformity and Stability * Small, Rugged, Thermowatt Construction for Low Thermal Resistance, High Heat Dissipation and Durability * Gate Triggering Guaranteed in Four Modes * Indicates UL Registered -- File #E69369 * Device Marking: Logo, Device Type, e.g., MAC15A6FP, Date Code MAXIMUM RATINGS (TJ = 25C unless otherwise noted) Rating Peak Repetitive Off-State Voltage(1) (TJ = -40 to +125C, Sine Wave 50 to 60 Hz, Gate Open) MAC15A6FP MAC15A8FP MAC15A10FP On-State RMS Current (TC = +80C)(2) Full Cycle Sine Wave 50 to 60 Hz (TC = +95C) Peak Nonrepetitive Surge Current (One Full Cycle Sine Wave, 60 Hz, TC = +80C) Preceded and followed by rated current Circuit Fusing (t = 8.3 ms) Peak Gate Power (TC = +80C, Pulse Width = 2.0 s) Average Gate Power (TC = +80C, t = 8.3 ms) Peak Gate Current (Pulse Width 1.0 sec; TC = 80C) Symbol VDRM, VRRM 400 600 800 IT(RMS) 15 12 ITSM 150 Amps Amps 1 2 3 Value Unit Volts http://onsemi.com ISOLATED TRIAC ( 15 AMPERES RMS 400 thru 800 VOLTS ) MT2 G MT1 I2t PGM PG(AV) IGM VGM V(ISO) TJ Tstg 93 20 0.5 2.0 10 1500 -40 to +125 -40 to +150 A2s Watts 1 Watt Amps Volts Volts 2 3 ISOLATED TO-220 Full Pack CASE 221C STYLE 3 PIN ASSIGNMENT Main Terminal 1 Main Terminal 2 Gate v v Peak Gate Voltage (Pulse Width 1.0 sec; TC = 80C) RMS Isolation Voltage (TA = 25C, Relative Humidity 20%) ( ) ORDERING INFORMATION Device MAC15A6FP Package ISOLATED TO220FP ISOLATED TO220FP ISOLATED TO220FP Shipping 500/Box 500/Box 500/Box p Operating Junction Temperature Storage Temperature Range C C MAC15A8FP MAC15A10FP (1) VDRM and VRRM for all types can be applied on a continuous basis. Blocking voltages shall not be tested with a constant current source such that the voltage ratings of the devices are exceeded. (2) The case temperature reference point for all TC measurements is a point on the center lead of the package as close as possible to the plastic body. (c) Semiconductor Components Industries, LLC, 1999 Preferred devices are recommended choices for future use and best overall value. 1 February, 2000 - Rev. 1 Publication Order Number: MAC15A6FP/D MAC15A6FP, MAC15A8FP, MAC15A10FP THERMAL CHARACTERISTICS Characteristic Thermal Resistance, Junction to Case Thermal Resistance, Case to Sink Thermal Resistance, Junction to Ambient Maximum Lead Temperature for Soldering Purposes 1/8 from Case for 10 Seconds Symbol RJC RCS RJA TL Max 2.0 2.2 (typ) 60 260 Unit C/W C/W C/W C ELECTRICAL CHARACTERISTICS (TC = 25C unless otherwise noted; Electricals apply in both directions) Characteristic Symbol Min Typ Max Unit OFF CHARACTERISTICS Peak Repetitive Blocking Current (VD = Rated VDRM, VRRM; Gate Open) TJ = 25C TJ = 125C IDRM, IRRM -- -- -- -- 10 2.0 A mA ON CHARACTERISTICS Peak On-State Voltage(1) (ITM = A Peak "21 VTM IGT -- 1.3 1.6 Volts mA Gate Trigger Current (Continuous dc) (Main Terminal Voltage = 12 Vdc, RL = 100 Ohms) MT2(+), G(+) MT2(+), G(-) MT2(-), G(-) MT2(-), G(+) Gate Trigger Voltage (Continuous dc) (Main Terminal Voltage = 12 Vdc, RL = 100 Ohms) MT2(+), G(+) MT2(+), G(-) MT2(-), G(-) MT2(-), G(+) Gate Non-Trigger Voltage (Main Terminal Voltage = Rated VDRM, RL = 100 , TJ = +110C) All 4 Quadrants Holding Current (Main Terminal Voltage = 12 Vdc, Gate Open, Initiating Current = mA) -- -- -- -- VGT -- -- -- -- VGD 0.2 IH -- -- -- -- -- 50 50 50 75 Volts 0.9 0.9 1.1 1.4 2.0 2.0 2.0 2.5 Volts -- 6.0 -- 40 mA "200 Turn-On Time (VD = Rated VDRM, ITM = 17 A, IGT = 120 mA, Rise Time = 0.1 s, Pulse Width = 2 s) t gt -- 1.5 -- s DYNAMIC CHARACTERISTICS Critical Rate of Rise of Commutation Voltage (VD = Rated VDRM, VRRM, ITM = 21 A, Commutating di/dt = 7.6 A/ms, Gate Unenergized, TC = 80C) (1) Pulse Test: Pulse Width 2.0 ms, Duty Cycle 2%. dv/dt(c) -- 5.0 -- V/s http://onsemi.com 2 MAC15A6FP, MAC15A8FP, MAC15A10FP Voltage Current Characteristic of Triacs (Bidirectional Device) + Current Quadrant 1 MainTerminal 2 + Symbol VDRM IDRM VRRM IRRM VTM IH Parameter Peak Repetitive Forward Off State Voltage Peak Forward Blocking Current Peak Repetitive Reverse Off State Voltage Peak Reverse Blocking Current Maximum On State Voltage Holding Current IH Quadrant 3 VTM MainTerminal 2 - IRRM at VRRM on state VTM IH off state + Voltage IDRM at VDRM Quadrant Definitions for a Triac MT2 POSITIVE (Positive Half Cycle) + (+) MT2 (+) MT2 Quadrant II (-) IGT GATE MT1 REF (+) IGT GATE MT1 REF Quadrant I IGT - (-) MT2 (-) MT2 + IGT Quadrant III (-) IGT GATE MT1 REF (+) IGT GATE MT1 REF Quadrant IV - MT2 NEGATIVE (Negative Half Cycle) All polarities are referenced to MT1. With in-phase signals (using standard AC lines) quadrants I and III are used. http://onsemi.com 3 MAC15A6FP, MAC15A8FP, MAC15A10FP TYPICAL CHARACTERISTICS 130 30 120 60 110 125C 150 to 180 90 80 0 = CONDUCTION ANGLE 2 4 6 8 10 12 14 16 IT(RMS), RMS ON-STATE CURRENT (AMP) dc 90 IGTM , GATE TRIGGER CURRENT (NORMALIZED) 3 2 OFF-STATE VOLTAGE = 12 Vdc ALL MODES TC, CASE TEMPERATURE (C) 1 0.7 0.5 100 0.3 -60 -40 -20 0 20 40 60 80 100 120 140 TJ, JUNCTION TEMPERATURE (C) Figure 1. RMS Current Derating PD(AV), AVERAGE POWER DISSIPATION (WATTS) 20 TJ = 125C 16 dc 12 8 = CONDUCTION ANGLE i F, INSTANTANEOUS FORWARD CURRENT (AMP) = 180 120 90 60 30 30 20 50 100 70 Figure 4. Typical Gate Trigger Current TJ = 25C 125C 4 0 0 2 4 6 8 10 12 14 16 IT(RMS), RMS ON-STATE CURRENT (AMP) 10 7 5 3 2 Figure 2. On-State Power Dissipation VGTM , GATE TRIGGER VOLTAGE (NORMALIZED) 3 2 OFF-STATE VOLTAGE = 12 Vdc ALL MODES 1 0.7 0.5 1 0.7 0.5 0.3 0.2 0.3 -60 -40 -20 0 20 40 60 80 100 120 140 0.1 0.4 0.8 1.2 1.6 2 2.4 2.8 3.2 3.6 4 4.4 TJ, JUNCTION TEMPERATURE (C) vT, INSTANTANEOUS ON-STATE VOLTAGE (VOLTS) Figure 3. Typical Gate Trigger Voltage http://onsemi.com 4 Figure 5. Maximum On-State Characteristics MAC15A6FP, MAC15A8FP, MAC15A10FP 3 I H, HOLDING CURRENT (NORMALIZED) 2 I TSM, PEAK SURGE CURRENT (AMP) GATE OPEN APPLIES TO EITHER DIRECTION 300 200 1 0.7 0.5 100 70 50 TC = 80C f = 60 Hz SURGE IS PRECEDED AND FOLLOWED BY RATED CURRENT 1 2 3 NUMBER OF CYCLES 5 7 10 0.3 -60 -40 -20 0 20 40 60 80 100 120 140 30 TJ, JUNCTION TEMPERATURE (C) Figure 6. Typical Holding Current r(t) TRANSIENT THERMAL RESISTANCE (NORMALIZED) Figure 7. Maximum Nonrepetitive Surge Current 1 0.5 0.2 0.1 0.05 ZJC(t) = r(t) * RJC 0.02 0.01 0.1 0.2 0.5 1 2 5 10 20 50 100 200 500 1k 2k 5k 10 k t, TIME (ms) Figure 8. Thermal Response http://onsemi.com 5 MAC15A6FP, MAC15A8FP, MAC15A10FP PACKAGE DIMENSIONS ISOLATED TO-220 Full Pack CASE 221C-02 ISSUE C -B- P -T- F N E C S SEATING PLANE NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. LEAD DIMENSIONS UNCONTROLLED WITHIN DIMENSION Z. DIM A B C D E F G H J K L N P Q R S Z INCHES MIN MAX 0.680 0.700 0.388 0.408 0.175 0.195 0.025 0.040 0.340 0.355 0.140 0.150 0.100 BSC 0.110 0.155 0.018 0.028 0.500 0.550 0.045 0.070 0.049 --- 0.270 0.290 0.480 0.500 0.090 0.120 0.105 0.115 0.070 0.090 MILLIMETERS MIN MAX 17.28 17.78 9.86 10.36 4.45 4.95 0.64 1.01 8.64 9.01 3.56 3.81 2.54 BSC 2.80 3.93 0.46 0.71 12.70 13.97 1.15 1.77 1.25 --- 6.86 7.36 12.20 12.70 2.29 3.04 2.67 2.92 1.78 2.28 H -Y- Q 123 A K Z L G D 3 PL J R 0.25 (0.010) M B M Y STYLE 3: PIN 1. MT 1 2. MT 2 3. GATE http://onsemi.com 6 MAC15A6FP, MAC15A8FP, MAC15A10FP Notes http://onsemi.com 7 MAC15A6FP, MAC15A8FP, MAC15A10FP ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. PUBLICATION ORDERING INFORMATION NORTH AMERICA Literature Fulfillment: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: ONlit@hibbertco.com Fax Response Line: 303-675-2167 or 800-344-3810 Toll Free USA/Canada N. American Technical Support: 800-282-9855 Toll Free USA/Canada EUROPE: LDC for ON Semiconductor - European Support German Phone: (+1) 303-308-7140 (M-F 1:00pm to 5:00pm Munich Time) Email: ONlit-german@hibbertco.com French Phone: (+1) 303-308-7141 (M-F 1:00pm to 5:00pm Toulouse Time) Email: ONlit-french@hibbertco.com English Phone: (+1) 303-308-7142 (M-F 12:00pm to 5:00pm UK Time) Email: ONlit@hibbertco.com EUROPEAN TOLL-FREE ACCESS*: 00-800-4422-3781 *Available from Germany, France, Italy, England, Ireland CENTRAL/SOUTH AMERICA: Spanish Phone: 303-308-7143 (Mon-Fri 8:00am to 5:00pm MST) Email: ONlit-spanish@hibbertco.com ASIA/PACIFIC: LDC for ON Semiconductor - Asia Support Phone: 303-675-2121 (Tue-Fri 9:00am to 1:00pm, Hong Kong Time) Toll Free from Hong Kong & Singapore: 001-800-4422-3781 Email: ONlit-asia@hibbertco.com JAPAN: ON Semiconductor, Japan Customer Focus Center 4-32-1 Nishi-Gotanda, Shinagawa-ku, Tokyo, Japan 141-8549 Phone: 81-3-5740-2745 Email: r14525@onsemi.com ON Semiconductor Website: http://onsemi.com For additional information, please contact your local Sales Representative. http://onsemi.com 8 MAC15A6FP/D |
Price & Availability of MAC15A10FP
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |